Actions

Difference between revisions of "Connecting Radios to Soundcards"

From The RadioReference Wiki

m
Line 86: Line 86:
 
* If you need to restore soundcard settings, or have a way to set different settings for different applications, then you should look into [http://www.softpedia.com/get/Multimedia/Audio/Other-AUDIO-Tools/QuickMix.shtml QuickMix].  
 
* If you need to restore soundcard settings, or have a way to set different settings for different applications, then you should look into [http://www.softpedia.com/get/Multimedia/Audio/Other-AUDIO-Tools/QuickMix.shtml QuickMix].  
  
 
+
----
 +
* Return to [[DXing Digital Utilities]]
  
 
[[Category:Live Audio FAQ]]
 
[[Category:Live Audio FAQ]]
 
[[Category:Software FAQ]]
 
[[Category:Software FAQ]]

Revision as of 12:59, 3 July 2019

Welcome to the Connecting Radios to Soundcards article. Soundcard software has come a long way in the last few years, and has the ability now to manipulate and use audio inputs in a variety of ways. For us scannists, 2 reasons invariably pop up;

  • I want to decode (or record) a signal I heard on my scanner - or -
  • I want to decode (or record) a signal I heard on my HF radio

This article discusses the basics of setting up Windows to accept audio from your radio. At the bottom, there are links to articles with numerous software packages, some of which can be used with a soundcard input.

Before we proceed, it should be noted that settings may appear different in different OSs, and with different PC distributors, who often put their own soundcard support software in their systems. The images -and text - in this article should be used as a guide, not as specific examples. In addition, connecting a soundcard to a ham transceiver is a much more critical function, as isolation between the transceiver and PC is a must. For extensive discussions on the subject, please see the Understanding Soundcard Interfacing website.

Windows Connections

How you get to your sound card (audio) settings varies depending on your Windows OS


Other Considerations

  • The Bit Rate is important; 8 and 16bit are the most common; high bitrates allow for smoother audio response and better throughput.
  • You can use Stereo and Mono Mix Recording settings to record real time audio from your computer, Internet, Chat Rooms, Programs, etc.
  • If you have onboard sound built into your mother board and find it's not working, or has very poor quality, you can pick up a cheap $30 Sound Blaster Sound Card from WalMart which supports 96000hz, and 24bit Sound
  • New PCs don't have any line or mic in jacks. You will need to use a USB driven soundcard adapter.


Cabling and Hookups

  • The use of shielded audio cable is strongly recommended. Make it as short as possible to minimize stray pickup.
  • Older laptops and PCs that have Line/Mic in jacks require a stereo jack (1/8 inch) as input. Simply wire one side (either right or left). It may also be possible to short the 2 sides together. Check any available documentation on your soundcard for specifics.
  • Laptops may require an attenuating patch cord, since their inputs may be designed to handle low-level inputs. If you hear distortion no matter what audio level you set, this is likely to be a cause.
  • A resistor across the jack is an easy way to assemble an attenuating patch cord. One way to find the correct value would be to connect a 10k audio taper potentiometer across the jack, along with a Volt Ohm Meter (VOM). Begin with maximum resistance, and slowly decrease it until the audio sounds normal. You may need to also adjust the levels in the soundcard's control panel. When the audio is satisfactory, note the reading on the VOM. You now have an idea of the resistor's value.


Questions and Answers

  • How can I get a date/time stamp on my recording?
    • Most stand alone recording programs like RecAll or ScanCorder, will tag the audio file with date/time and duration.
  • No audio is heard through the PC speakers using either 'Line In' or 'Mic In' jacks on the soundcard.
    • Make sure that neither of these selections has been muted in the control panel for the soundcard (see above)
  • An A/C type hum is heard, even when receiving nothing.
    • Double click on your speaker icon on your taskbar, go to Options, Properties, change "Adjust volume" to Recording, hit OK, and under Mic, there should be an advanced, and see if 20 db boost is enabled. (Evan Platt via Scan-L)
    • Many Uniden receivers put a resistor in the headphone jack circuit to limit the output. This is in the ground side of the jack and can cause hum if you are trying to use it for a tape input. According to the manual, the 796D has a programable tape output on the rear panel. See page 18 of the manual. If you still have hum, get a ground loop isolator such as these from Best Buy and the necessary adapters.
  • My Stereo Mix Setting/Soundcard is Disabled. How can I enable it?
    • You may need to right click on the setting in Properties and enable it. If that doesn't work, try updating the drivers from the distributor's website. Lastly, you may be able to use the Stereo Mix software to create a virtual sound card.


Scanner Related Issues
  • How Can I Record Using an Uniden BC796D?
    • The BC796D (and possibly the BC785D) has a tape output jack; however, it seems to activate after a 2 second delay. To get around this, connect to the speaker out jack instead
  • Which RS Scanners can or cant log and record audio?
    • Older Radio Shack scanners- with the exception of the PRO-2052 (which is really a Uniden clone) cannot log frequency or talkgroup information. It's not provided for in the firmware. However, the PRO-197, 106, 651, 652 as well as the Whistler WS-1040 and 1065 (which are RS clones of the GRE PSR-500 and 600) can do this with the proper software


Soundcard-Driven Software

Regardless of the application you are trying to execute, if you have Windows Vista You may need to check to see if your software is compatible with it. XP support is far more widespread, with less problems; however it too has a compatiblity feature that allows you to tell XP if your particular program need to run as if it were in Win95, 98, etc. or in other modes/colors.

  • If you need to restore soundcard settings, or have a way to set different settings for different applications, then you should look into QuickMix.