Actions

Difference between revisions of "Pro-2055"

From The RadioReference Wiki

 
(30 intermediate revisions by 8 users not shown)
Line 12: Line 12:
 
==General Specifications==
 
==General Specifications==
 
===Features===
 
===Features===
* [[Rebanding]] supported? <font color=Orange> NOT KNOWN </font> It appears that the scanner must be returned to Radio Shack for a logic and display board retrofit 'if' it is to be supported.
+
* Can be updated to support [[Rebanding]]? {{color|red|NO}}
** See this [http://www.strongsignals.net/access/news/news.cgi?type=single&section=radio&entry=1510 article] on the Strong Signals website for more information, or 800Reband - WPAScanner [http://www.wpascanner.com/wiki/index.php/800Reband Radio Shack Scanner Rebanding Chart] that has contradictory information as reported by Monitoring Times, Radio Rumors. The fist link information pertains to the [[Pro-97]]; however it is assumed that the support will be applied in a similar manner. More information is required.
 
  
 
*A '''cloning cable''' may be fabricated using 2 1/8 inch mono jacks and shielded cable
 
*A '''cloning cable''' may be fabricated using 2 1/8 inch mono jacks and shielded cable
Line 104: Line 103:
  
 
==Related Pages==
 
==Related Pages==
* [http://myweb.cableone.net/marksscanners/97/97.html Easier to Read PRO-97/2055 Manual]
+
* [http://new.marksscanners.com/97/97.shtml Easier to Read Pro 97/2055 Manual]
* [http://tinyurl.com/92fwn Radio Shack website statement on Rebanding]
+
* [[Getting Started with your PRO-97 and PRO-2055]]
* [[Programming Shortcut pro-2055]]
 
  
==Software==
+
==Discriminator Tap for PRO-2055==
* [http://www.starrsoft.com/software/win97/default.asp Win97]
+
Use a 10K ohm 1/4watt resistor soldered to TP4 to the tip of a case mount 3.5mm (1/8 inch) metal mono jack. Use a .002 uF ceramic capacitor between ground and the tip of the jack.
* [http://www.scancat.com/scancat-lite Scancat Lite Plus]
+
[[Image:pro-2055_tap.jpg|thumb|none|Pro-2055 Discriminator Tap]]
* [http://www.psredit.com/psredit300/ PSREdit300 with support for the Pro-2055]
 
* [http://www.starrsoft.com/software/Win96/Cables/cables.html Scanner cables]
 
* [http://www.greamerica.com/scanner_accessories.html GRE USB Programming cable]
 
  
==Yahoo Groups and Mailing Lists (software and receiver support)==
+
==Mailing Lists / Forums==
* [http://groups.yahoo.com/group/PRO-2055/ PRO-2055 Yahoo group]
+
* {{Forum|radio-shack-scanners.81|RadioReference Radio Shack}}
* [http://groups.yahoo.com/group/PRO-2055_scanner/ PRO-2055-scanner Yahoo group]
+
* [https://www.facebook.com/groups/448987651918830 Radio Scanner World]
* [http://groups.yahoo.com/group/p97/ p97 Yahoo group (.p97 files)]
+
* [https://www.facebook.com/groups/667031203353717 Radio Scanners]
* [http://strongsignals.net/access/forums/viewforum.php?f=10 Strong Signals GRE Message board]
+
* [https://www.facebook.com/groups/4188584134 Scanner Enthusiasts]
* [http://strongsignals.net/access/forums/viewforum.php?f=12 Strong Signals Radio Shack Message board]  
+
* [https://www.facebook.com/groups/2889562301118379 Radio Scanner Help and Chat]
* [http://rsproscanners.proboards22.com/index.cgi Radio Shack PRO scanners message board]
 
* [http://www.radioreference.com/forums/forumdisplay.php?f=81 RadioReference Radio Shack forum]
 
  
==Programming and Keyboard Tricks==
+
==Pro-2055 Scanners for Sale==
=== Restoring The 155 Preset Frequencies ===
+
*[[Pro-2055 eBay Listings]]
# Turn the scanner OFF and then turn ON again.
 
# When the Multi-system Trunking Scanner appears, press PGM.
 
# Press 1
 
=== More than 1 Trunk System in a bank===
 
* You may program more than 1 trunk system in a bank provided you seperate them with 1 conventional channel
 
===Manually Changing the Welcome Message===
 
To change the startup message on the PRO-2055 scanner:
 
 
 
1. Turn on the scanner.<br>
 
2. Change to any standard FM channel. <br>
 
3. Press [PGM] to enter program mode.<br>
 
4. Press [FUNC] + [TEXT]. The display will read:
 
    Start Message<br>
 
    Edit 1st line:<br>
 
5. Enter the text you wish and press [ENT] to move to the second line, then the third, and so on.<br>
 
<small> Thanks to Matthew on rec.radio.scanner for the procedure</small>
 
 
 
== eBay Listings == 
 
<ebay>Radio Shack ("PRO-2055","PRO2055")</ebay>
 
  
 
Return to [[Radio Shack Scanners]]
 
Return to [[Radio Shack Scanners]]
  
 
+
[[Category:Radio Shack Scanners]]
 
[[Category:Desktop Scanners]]
 
[[Category:Desktop Scanners]]
 
[[Category:Mobile Scanners]]
 
[[Category:Mobile Scanners]]
[[Category:Trunking Scanners]]
 
 
[[Category:Analog Trunktrackers]]
 
[[Category:Analog Trunktrackers]]
 +
[[Category:Radio Models]]

Latest revision as of 09:52, 9 April 2021

Pro-2055

The Pro-2055 was manufactured for Radio Shack by GRE America Inc

The same scanner as the Pro-97 but as a base/mobile. Trunk tracker three technology. Can use Win97 to program with your computer. Note that due to firmware limitations, computer control is not possible.

This unit can be used as a desktop scanner or mounted in a vehicle.* Alphanumeric display shows ID code or can be programmed with service name. Backlit display and keypad for low-light use. Clones with the popular PRO-97 handheld scanner (#20-527).

Also see the Pro-97 page. All utilities and links listed there also apply to the PRO-2055.


General Specifications

Features

  • A cloning cable may be fabricated using 2 1/8 inch mono jacks and shielded cable
  • 1000-channel memory divided into ten banks lets you store up to 1000 frequencies
  • 5 ID lists, 30 IDs per list, 150 IDs per bank
  • Adjustable ID delay
  • Lock out IDs in 'open' mode
  • 150+ most popular national frequencies preprogrammed
  • Covers most popular 800MHz triple-trunking police/fire/emergency systems in most metropolitan areas
  • UHF, 800, 900, Motorola, LTR, EDACS (GE/Ericsson) capability
  • Use as a desktop scanner or mount in, under or on dash of vehicle* with included DIN-E hardware
  • Signal stalker II—searches for nearby frequency transmissions within approximately 1000 feet of the radio. Scanner will automatically jump to nearby transmission and display frequency
  • Skywarn button—hear storm reports from spotters near your location minutes before they are broadcast on TV or radio. (requires one-time programming of one frequency into memory)
  • Weather priority
  • 16 character alphanumeric display can display ID code or service name
  • Backlit display and keypad
  • Clones to another 2055 or the popular PRO-97 handheld scanner—download information on the handheld to the desktop scanner, no need to program separately
  • CTCSS/DCS (Continuous Tone Coded Squelch System/Digital Coded Squelch) receive and detect
  • 1 priority channel

Specifications

  • Frequencies: 25-54, 108-136.99166, 137-174, 216.0025-225, 225-406, 406-512, 800-960 (except cellular), 1240-1300MHz
  • FM/AM/PL/DPL mode, user selectable
  • Triple conversion
  • 60-channel scan per second, 75-step search per second
  • 5, 6.26, 7.5, 8.333, 12.5, 25KHz step (preset by band - not user selectable)
  • 50-frequency search skip
  • Air, police-fire, Ham, Marine, WX, FRS/GMRS/MURS and CB service search
  • WX and SAME alert with FIPS operation—get alerts for only your county (will not alert in SAME mode unless you have entered the FIPS code for your county)
  • PC interface
  • 20dB attenuator (global or by-channel)
  • Lock out, lock out review, delay and reset
  • EPPROM memory backup—will not lose programming if power is lost
  • Dimensions (LWH): 7.2x5.3x2.2" (18.29x13.46x5.59cm)
  • Includes AC and DC adapters for desktop or vehicle* use
  • Takes ADAPTAPLUG type "T" for power supply - now discontinued at Radio Shack.

RR System Compatibility

This scanner is compatible with the following Trunking System Types and System Voices used in the RadioReference Database, of course you must verify that the scanner will cover the appropriate frequency range:

  • System Types:
    • Motorola Type I
    • Motorola Type II
    • Motorola Type IIi Hybrid
    • Motorola Type II Smartnet
    • Motorola Type II Smartzone
    • Motorola Type II Smartzone Omnilink
    • EDACS Standard (Wide)
    • EDACS Standard Networked
    • EDACS SCAT
    • LTR Standard
  • System Voices:
    • Analog

Reviews and User Opinions

Related Pages

Discriminator Tap for PRO-2055

Use a 10K ohm 1/4watt resistor soldered to TP4 to the tip of a case mount 3.5mm (1/8 inch) metal mono jack. Use a .002 uF ceramic capacitor between ground and the tip of the jack.

Pro-2055 Discriminator Tap

Mailing Lists / Forums

Pro-2055 Scanners for Sale

Return to Radio Shack Scanners