Actions

Difference between revisions of "Raspberry Pi RTL-SDR Broadcastify"

From The RadioReference Wiki

Line 81: Line 81:
 
== Command for AM Aviation Scanning ==
 
== Command for AM Aviation Scanning ==
  
  rtl_fm -M am -f 124.55M -f 133.4M -f 121.6M -l 65 -p 69 -g 40 -t 0 -E pad -s 8k  
+
  rtl_fm -M am -f 124.55M -f 133.4M -f 121.6M -l 65 -p 69 -g 40 -t 0 -E pad -s 8k |
  | lame -r -s 8 -m m -b 16 --cbr --lowpass 4 --scale 16 - -  
+
  lame -r -s 8 -m m -b 16 --cbr --lowpass 4 --scale 16 - - |
| ezstream -c /etc/ezstream_bcfy.xml &
 
 
 
rtl_fm - command line tuner for rt stick
 
-M am          tune to AM Mode
 
-f 124.55M      tune to 124.55 MHz (use multiple -f entries to scan through frequencies)
 
-l 65          set scanning squelch to 65 (adjust as needed)
 
-p 69          ppm offset
 
-g 40.2        gain (0-49.6) - adjust as needed
 
-t 0            scanning delay (I set to 0, default is 10)
 
-E pad          when squelch is enabled pad output with zeros (required when broadcasting)
 
-s 8k          sample at 8k
 
 
 
which is then piped to the mp3 lame encoder...
 
 
 
lame - MP3 encoder
 
-r          accept raw data input
 
-s          encode at 8k
 
-m          encode mono
 
-b          encode at 16kbs bitrate
 
--cbr        use Broadcastify’s mp3 cbr standard
 
--lowpass 4  use a low pass filter of 4
 
--scale 16  turn up the volume
 
 
 
which is then piped to ezstream
 
 
 
 
  ezstream -c /etc/ezstream_bcfy.xml
 
  ezstream -c /etc/ezstream_bcfy.xml

Revision as of 19:42, 30 July 2015

These instructions show you how to purchase and setup a completely self contained Raspberry Pi with an RTL-SDR stick(s) to broadcast a live audio feed to Broadcastify.com

Purchase Equipment

Raspberry Pi 2 Model B Project Board - 1GB RAM - 900 MHz Quad-Core CPU

RTL-SDR - RTL2832U & R820T USB Stick

Male MCX Connector to...

Power Supply for Raspberry Pi

Memory Card for Raspberry Pi

Case for Raspberry Pi

Install pre-reqs and update raspberry pi to latest version

sudo apt-get update
sudo apt-get upgrade
sudo apt-get install git cmake libusb-1.0-0.dev build-essential
sudo apt-get install libmp3lame-dev libvorbis-dev libshout-dev
sudo rpi-update && sudo reboot

Install the latest rtl-sdr code

This latest git release is needed for padding zeros when squelch is enabled (-E pad option)

git clone https://github.com/keenerd/rtl-sdr/
cd rtl-sdr/
mkdir build
cd build
cmake ../
make
sudo make install
sudo ldconfig
sudo mv $HOME/rtl-sdr/rtl-sdr.rules /etc/udev/rules.d/rtl-sdr.rules

Blacklist the kernel's bundled RTL drivers

We do this so we don't conflict with the RTL drivers we're about to install

sudo su -
echo "blacklist r820t" >> /etc/modprobe.d/dvb-blacklist.conf
echo "blacklist rtl2832" >> /etc/modprobe.d/dvb-blacklist.conf
echo "blacklist rtl2830" >> /etc/modprobe.d/dvb-blacklist.conf
echo "blacklist dvb_usb_rtl28xxu" >> /etc/modprobe.d/dvb-blacklist.conf
exit

Install and configure ezstream

sudo apt-get install ezstream

Create this configuration file at /etc/ezstream_bcfy.xml and replace with your mount, password, and stream name

<ezstream>
    <url>http://audio#.broadcastify.com:80/your_mount</url>
    <sourcepassword>your_source_password</sourcepassword>
    <format>MP3</format>
    <filename>stdin</filename>
    <svrinfoname>Stream Name</svrinfoname>
    <svrinfourl>http://www.broadcastify.com</svrinfourl>
    <svrinfogenre>Scanner</svrinfogenre>
    <svrinfodescription></svrinfodescription>
    <svrinfobitrate>16</svrinfobitrate>
    <svrinfochannels>1</svrinfochannels>
    <svrinfosamplerate>22050</svrinfosamplerate>
    <svrinfopublic>0</svrinfopublic>
</ezstream>

Command for AM Aviation Scanning

rtl_fm -M am -f 124.55M -f 133.4M -f 121.6M -l 65 -p 69 -g 40 -t 0 -E pad -s 8k |
lame -r -s 8 -m m -b 16 --cbr --lowpass 4 --scale 16 - - |
ezstream -c /etc/ezstream_bcfy.xml