Difference between revisions of "Uniden Headphone Jack Modification"
From The RadioReference Wiki
(Created page with "This modification describes a procedure that can be used if you plugged headphones or a speaker into the speaker out on the BCD996T, and you later find out that the audio has gon...") |
(Documented some other more reasonable solutions along with providing sub-headings) |
||
| Line 1: | Line 1: | ||
| + | == Uniden Headphone Jack Fix == | ||
This modification describes a procedure that can be used if you plugged headphones or a speaker into the speaker out on the BCD996T, and you later find out that the audio has gone dead.<br> | This modification describes a procedure that can be used if you plugged headphones or a speaker into the speaker out on the BCD996T, and you later find out that the audio has gone dead.<br> | ||
'''NOTE:''' Performing this modification voids the warranty<br> | '''NOTE:''' Performing this modification voids the warranty<br> | ||
| Line 14: | Line 15: | ||
#Then place a bead of solder between the two posts as shown in the red box, these are the #2 and #3 posts when referencing the case as a starting point. (figure 3) | #Then place a bead of solder between the two posts as shown in the red box, these are the #2 and #3 posts when referencing the case as a starting point. (figure 3) | ||
| + | <small> Thanks to canav844 for posting this modification</small> | ||
| − | + | == Other Solutions == | |
| − | + | * Soldering on close connection PCB boards scares the crap out of me. A far better solution is to follow the two wires to the J11 onboard connector and insert a jumper wire between between the two wires on the back of the female connector for the J11 pins! This gives the user the option to remove the jumper wire when they want to use the ear plug, but requires removing the covers to do so. | |
| − | + | * Another idea is to solder a switch between the two wires of the J11 connector. | |
| + | * And yet another idea is to track down the original Uniden part and replace the part yourself, as the solder connections for the ear plug are space further apart then the #2 and #3 pins of the above tip! When somebody finds the original parts, please publish the part number and supplier. (ie. Digikey or Mouser electrical parts suppliers) | ||
[[Category:Modifications]] | [[Category:Modifications]] | ||
Revision as of 13:17, 23 November 2011
Uniden Headphone Jack Fix
This modification describes a procedure that can be used if you plugged headphones or a speaker into the speaker out on the BCD996T, and you later find out that the audio has gone dead.
NOTE: Performing this modification voids the warranty
NOTE: This modification will disable the muting of the speaker output when headphones are plugged in
Figure 1
Figure 2
Figure 3
- First remove the black case surround (figure 1)
- The internal case around the headphone jack needs to be opened. Remove the highlighted screws on both sides (figure 2)
- Then place a bead of solder between the two posts as shown in the red box, these are the #2 and #3 posts when referencing the case as a starting point. (figure 3)
Thanks to canav844 for posting this modification
Other Solutions
- Soldering on close connection PCB boards scares the crap out of me. A far better solution is to follow the two wires to the J11 onboard connector and insert a jumper wire between between the two wires on the back of the female connector for the J11 pins! This gives the user the option to remove the jumper wire when they want to use the ear plug, but requires removing the covers to do so.
- Another idea is to solder a switch between the two wires of the J11 connector.
- And yet another idea is to track down the original Uniden part and replace the part yourself, as the solder connections for the ear plug are space further apart then the #2 and #3 pins of the above tip! When somebody finds the original parts, please publish the part number and supplier. (ie. Digikey or Mouser electrical parts suppliers)