Actions

Programming Shortcut Pro-92

From The RadioReference Wiki

Pro-92 Cheat Sheet 

Note: If the system is Mot I or IIi, set the Fleetmap in the last section prior to 
other programming.

Programming
Storing known non trunked frequencies
1. Press Manual, Press three digits to get the bank and channel number desired then Press 
   Manual again.  (upper left should read Mxxx for your bank and channel number)
2. Press PGM, (upper left should change from M to P) 
3. Enter the frequency using the numbered keys in the format xx.xxxxx, xxx.xxxxx or xxxx.xxxxx.  
4. If needed, Press Mode to change the receiver mode.
5. Press ENTER
6. To Alpha Tag a freq, press TEXT and using the letters above the numbers, text in the name.
7. Press ENTER
8. Press PGM or UP button and repeat steps 3 through 7 until all desired frequencies are entered 
   in selected bank.

Storing known trunked frequencies
Note:  	1. EDACS must start in channel 01 of bank not channel 00, and must 
       	follow a listed order called LCN.
        2. LTR regular channels need not be in LCN order in this scanner.
1. Press Manual, Press three digits to get the bank and channel number desired then Press 
   Manual again.  (upper left should read Mxxx for your bank and channel number)
2. Press PGM then Trunk
3. Press Mode for MO (Motorola) or ED (EDACS) or LT (LTR).
4. Press PGM
5. Enter the frequency using the numbered keys
6. Press ENTER  
7. To Alpha Tag a freq, press TEXT and using the letters above the numbers, text in the name.
8. Press ENTER
9. Press PGM or UP button and repeat steps 4 through 8 until all desired frequencies are entered 
   in selected bank.

Storing frequency Text Tags if not stored previously.
1. Press Manual, Press three digits to get the bank and channel number desired then Press 
   Manual again.  (upper left should read Mxxx for your bank and channel number)
2. Press PGM, (upper left should change from M to P)
3. Press Text, the cursor appears on line 3.
4. Using the numbered keys text in the line up to 12 characters.  The letters above each number 
   will help in the selection.  Example, POLICE DISP (11 characters counting the space) The 
   first letter is P, Press the number 7 then the number 1 for P. (7 will open the four numbers 
   PQRS and by selecting 1 is for the first of these four.  A 7 then 2 would get the letter Q.  
   Press up of down to move the courser back an fourth or to correct a mistake.
		5. Press Enter
			Note: Chart on page 39 for other text options.

Talk Group ID’s
These are Identification assigned by the manager of the system you desire to scan.

Storing unknown ID’s
1. When the scanner stops on a conversion, Press Trunk, the bottom line will indicate where the 
   ID is saved 
   Note:  If an ID was already stored, the bottom line will display ID was saved.
	  Storing Known ID’s
1. Select out all banks except desired bank ie. While scanning press each numbered bank to 
   deselect it except your desired bank.
2. Press PGM.
3. Press Trunk.
4. Press down until I+bank X00 appears at the top left..
5. Press mode, if needed for MO or ED or LTR.
6. Enter the ID number, if necessary use the period for a hyphen.
7. Press Enter.
8. Press up and repeat 6, 7 and 8 until all are entered.

Scanning Banks 

Turn Radio on, the last bank(s) selected will start scanning.  
Note: If the radio was in search mode when turned off, the radio will continue that search 
pattern when turned on until Scan or manual is pressed.

To change scanning banks. 
1. Press the number associated with desired bank.  The number on top line of display will either 
   be on or off accordingly. 

To change from Open Mode to Closed Mode (or the reverse).
1. Press Manual then the bank and number you want to change.
2. Press FUNC then 5 (Bank Open of Bank Closed will display).
3. Alternately, while scanning in a bank, when the radio stops on a call, Press FUNC then 5 
   (Bank open or Bank Closed will display). 
Note: In the Open Mode the scanner will stop on any transmission of all talk groups in a system.  
In the Closed Mode the scanner will stop on only unlocked stored ID’s.

Setting Fleetmaps for Type I and IIi hybrid systems 

1. While in your Motorola bank, Press PGM
2. Press TRUNK
3. Press FUNC then 8  
4. Your screen should read as follows:
                                            Block o size
                                            Code.  Use 15
                                            for type II.
                                            S-00
5. Using the numbered keys, enter the two-digit code for Block O, ie S-3 would be 03 for entry.  
6. Press ENTER. The top line will change to the next block waiting for new entry on line 4.
7. Repeat  step 5 and 6 until all codes are entered. 
       Note, S-12 will use two blocks, S-13 will use 4 blocks and S-14 will use all blocks.
8. Press SCAN

For more information on programming EDACS systems, please see the Pro 92/2067 EDACS Programming Guide (PDF)