Difference between revisions of "Programming Shortcut Pro-163 Pro-164"
From The RadioReference Wiki
(Created page with "==To program a Bank for Trunking== #Press PROG, then press TRUNK. #Press FUNC, then use an UP or DOWN ARROW to select a bank. #Repeatedly press MODE to select a trunking mode (Mo...") |
|||
(4 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | ==To program a Bank for Trunking== | + | This article applies to the following scanners: |
+ | * GRE [[PSR-300]] | ||
+ | * GRE [[PSR-400]] | ||
+ | * RS [[Pro-163]] | ||
+ | * RS [[Pro-164]] | ||
+ | |||
+ | |||
+ | '''Bold text'''==To program a Bank for Trunking== | ||
#Press PROG, then press TRUNK. | #Press PROG, then press TRUNK. | ||
#Press FUNC, then use an UP or DOWN ARROW to select a bank. | #Press FUNC, then use an UP or DOWN ARROW to select a bank. | ||
− | #Repeatedly press MODE to select a trunking mode (Motorola). | + | #Repeatedly press MODE to select a trunking mode (Motorola, EDACS,LTR). |
#Press PROG. | #Press PROG. | ||
#Enter the first control channel freq. and press ENTER. | #Enter the first control channel freq. and press ENTER. | ||
− | #Repeatedly press MODE to select a trunking mode (Motorola). | + | #Repeatedly press MODE to select a trunking mode (Motorola, EDACS, LTR). |
#Press PROG or the UP ARROW to advance to the next channel. | #Press PROG or the UP ARROW to advance to the next channel. | ||
#Enter the next control channel freq. and press ENTER. | #Enter the next control channel freq. and press ENTER. | ||
− | #Repeatedly press MODE to select a trunking mode (Motorola). | + | #Repeatedly press MODE to select a trunking mode (Motorola, EDACS, LTR). |
#After the last control channel freq., press ENTER, then press SCAN. | #After the last control channel freq., press ENTER, then press SCAN. | ||
Now you should start to see all active Talk Group IDs (TGs). | Now you should start to see all active Talk Group IDs (TGs). | ||
Line 22: | Line 29: | ||
#Use the UP or DOWN ARROW to select a bank. | #Use the UP or DOWN ARROW to select a bank. | ||
#Press FUNC then •/DELAY. | #Press FUNC then •/DELAY. | ||
− | |||
==Programming the Sub-Banks (Saving Talk Group IDs)== | ==Programming the Sub-Banks (Saving Talk Group IDs)== | ||
Line 50: | Line 56: | ||
<small>thanks to DickH for the procedure</small> | <small>thanks to DickH for the procedure</small> | ||
− | [[Category:Programming FAQs and Tips]] | + | [[Category:Programming FAQs and Tips for Radio Shack Scanners]] |
Latest revision as of 23:04, 9 December 2019
This article applies to the following scanners:
Bold text==To program a Bank for Trunking==
- Press PROG, then press TRUNK.
- Press FUNC, then use an UP or DOWN ARROW to select a bank.
- Repeatedly press MODE to select a trunking mode (Motorola, EDACS,LTR).
- Press PROG.
- Enter the first control channel freq. and press ENTER.
- Repeatedly press MODE to select a trunking mode (Motorola, EDACS, LTR).
- Press PROG or the UP ARROW to advance to the next channel.
- Enter the next control channel freq. and press ENTER.
- Repeatedly press MODE to select a trunking mode (Motorola, EDACS, LTR).
- After the last control channel freq., press ENTER, then press SCAN.
Now you should start to see all active Talk Group IDs (TGs).
- There are two trunking modes, OPEN and CLOSED:
- OPEN lets you hear ALL active TGs
- CLOSED lets you hear ONLY the TGs you have put into the SUB-BANKS.
- “–” appears for CLOSED mode and “+” appears for OPEN mode under the channel number.
- To set OPEN or CLOSED mode for the bank that is ON, Press FUNC then ./DELAY.
- To set OPEN or CLOSED mode for another bank
- Press MAN.
- Use the UP or DOWN ARROW to select a bank.
- Press FUNC then •/DELAY.
Programming the Sub-Banks (Saving Talk Group IDs)
Each of the 10 banks contains 5 sub-banks that each hold 30 Talk Group IDs. To define a Talk Group ID:
- Press PROG, then press TRUNK to enter the ID program mode.
- Press FUNC, then use UP or DOWN ARROW to select a bank.
- Repeatedly press MODE to select a trunking mode (Motorola, EDACS, or LTR).
- Repeatedly press TRUNK to select the sub-bank.
- Press UP or DOWN ARROW to select the location where to store the Talk Group ID.
- Use the number keys to enter the Talk Group ID:
- Press ENT.
Turning Sub-Banks ON or OFF
- To turn off a sub-bank
- Press TRUNK repeatedly to select the desired sub-bank.
- Press FUNC then 1 to turn the sub-bank on or off.
- To turn off a sub-bank while scanning
- When the scanner stops on a transmission, press FUNC.
- Press TRUNK. The display indicates which sub-bank is turned on or off. The active sub-bank number appears.
- Press FUNC and the number of the sub-bank you desire to turn on or off. For example to turn sub-bank 4 on or off, press FUNC. Then press 4.
- Note: This function activates when the receiving channel bank is in CLOSED mode.
thanks to DickH for the procedure