|
|
Line 1: |
Line 1: |
− | <pre>Programming for Trunking.
| |
| | | |
− | 1. Press and hold TRUNK until you hear two beeps, all 20 bank numbers should be flashing.
| |
− | 2. Press the number for the bank you want to program, E2-800 should be on the display and your bank
| |
− | number should be upper left.
| |
− | 3. If your system is Motorola type II then leave E2-800 in place. (for other systems, see Other
| |
− | Trunking Systems below)
| |
− | 4. Press E, Channel 1 of your bank should appear.
| |
− | 5. Using the numbered keys enter the first frequency,
| |
− | 6. Press E
| |
− | 7. Press ^ button, and enter the second frequency,
| |
− | 8. Press E
| |
− | 9. Repeat step 7 and 8 until all frequencies are entered.
| |
− | 10. When completed press TRUNK twice, your bank should be flashing on the top left.
| |
− | 11. Press SEARCH,
| |
− | You should now see ----- on the display until the scanner stops on a conversation. Then if the
| |
− | system type is E2-800/900 Motorola, the display will show from 2 to 5 numbers, which is an ID.
| |
− | If type I or IIi it may list XXX-XX, if EDACS it may be XX-XXX.
| |
− |
| |
− | Programming ID’s
| |
− | 1. Press SCAN
| |
− | 2. Press ^ button (----- should be on the display)
| |
− | 3. Navigate up or down until the number 1 appears on the left and a smaller number 1 is in upper left
| |
− | 4. Using the numbered keys, enter the 2 to 5 digits ID for E2-800/900 or (note, for Mot Type I or
| |
− | EDACS, ID’s use the period key for the hyphen).
| |
− | 5. Press E
| |
− | 6. Press ^ button (the number on left will increase with each entry)
| |
− | 7. Repeat steps 4 through 6 until all known ID’s are entered
| |
− | Note: after programming 10 ID’s, the number 1 appears on the left again and a number 2 appears in
| |
− | the upper left, this is a new ID Scan List. The scanner has 5 of these Scan Lists (sub-banks) for
| |
− | a total of 50 ID’s per scan bank.
| |
− |
| |
− | Other Trunking Systems
| |
− | E2-900=Mot 900, at step 2 under Programming for Trunking above, press ^ button repeatedly until
| |
− | E2-900 appears on display, then follow steps 4 through 11 in that section until all frequencies
| |
− | are entered.
| |
− |
| |
− | E2-Hi=Mot VHF, at step 2 under Programming for Trunking above, press ^ button repeatedly until
| |
− | E2-Hi appears on display, then follow steps 4 through 11 in that section until all frequencies
| |
− | are entered. Then these five steps.
| |
− | 1. Press DATA/ALERT
| |
− | 2. Key in the BRS (base frequency) Press E.
| |
− | 3. Press DATA/ALERT
| |
− | 4. Key in the OFS (offset) Press E.
| |
− | 5. Press TRUNK and follow steps 4 through 11 above
| |
− |
| |
− | E2-UHF=Mot UHF 400, at step 2 under Programming for Trunking above, press ^ button until E2-UHF
| |
− | appears on display, then follow steps 4 through 11 in that section until all frequencies are
| |
− | entered. Then follow steps 1 through 5 for E2-Hi above.
| |
− |
| |
− | Ed=EDACS, at step 2 under Programming for Trunking above, press ^ button repeatedly until Ed
| |
− | appears on the display, then follow steps 4 through 11 in that section until all frequencies
| |
− | are entered.
| |
− |
| |
− | E1=Mot, User set fleetmap (not preset) because most are not preset.
| |
− | 1. Press and hold TRUNK until you hear two beeps, all 20 bank number should be flashing.
| |
− | 2. Press the number for the bank you want to program, E2-800 should be on the display and your
| |
− | bank, number should be upper left.
| |
− | 3. Press ^ button repeatedly until E1 appears in the display, then press E
| |
− | 4. Press DATA
| |
− | 5. Press up/HOLD repeatedly until USr is in the display, then press DATA
| |
− | 6. b0 S - 0 should be on the display; b=Block, 0=block 0; S=Size code, 0=Size code 0. (note)
| |
− | by pressing ^ button repeatedly, notice the number after the S (Size Code) increases and the b0
| |
− | flashes. b0 is the first Block, if your source gives you a size for Block 0, stop or go back by
| |
− | pressing LIMIT to your Size code for this block.
| |
− | 7. Press E b0 changed to b1 and S - 0 reappears.
| |
− | 8. Repeat step 6 and 7 until all size codes are entered.
| |
− |
| |
− | Note, If any size code is 12, then it will take two blocks. If any size code is 13, then it will
| |
− | take four blocks. If your size code is 14, then it will take all blocks.
| |
− |
| |
− | After all 8 blocks are programmed (blocks 0 through 7) press Search. If your frequencies are
| |
− | programmed, you should pick up communications and the type I (or II if Hybrid) ID's should be
| |
− | present during Comms.
| |
− |
| |
− | Program ID’s using the Programming ID’s section above.
| |
− |
| |
− | Note: for the new Pro-2052 regarding changing from one trunk scanner bank to another.
| |
− |
| |
− | Press and hold TRUNK, all banks should now be flashing.
| |
− | Press TRUNK
| |
− | Press SCAN, then press your intended bank number and deselect the bank you no longer intend to Scan.
| |
− | Press TRUNK
| |
− |
| |
− | Document by Frank Monroe</pre>
| |