Difference between revisions of "IC-R7100"
From The RadioReference Wiki
(add new Lynovation links) |
|||
(22 intermediate revisions by 5 users not shown) | |||
Line 2: | Line 2: | ||
This page lists links, related pages and software support for the Icom R-7100 receiver. The technical specifications can | This page lists links, related pages and software support for the Icom R-7100 receiver. The technical specifications can | ||
be viewed [http://www.icomamerica.com/support/archive/receivers/ic-r7100a.asp here] (From the Icom website). | be viewed [http://www.icomamerica.com/support/archive/receivers/ic-r7100a.asp here] (From the Icom website). | ||
− | |||
==General Specifications== | ==General Specifications== | ||
Line 60: | Line 59: | ||
* [[R7100 Discriminator Tap Notes]] | * [[R7100 Discriminator Tap Notes]] | ||
* Here is a [http://www.radioreference.com/digital/dig/ICOMSLICER.PDF schematic] (PDF file) for an interface used with [[Trunker]] and a Icom [[IC-R7000]]. For this example, a PRO-43 scanner is used to obtain the data channel. The interface obtains power from the Icom, so there is no issue with weak ports not being able to power the slicer. The IC Chip used is a MAX203 for minimum parts count, but a MAX232 would work just as well. The MAX203 can be obtained from Digi-Key. This interface has also been tested with an Icom R7100. This interface may also work for other radios that use TTL serial levels if another source of 9-12V is available, or 5V if the regulator is left out. (Thanks to Gene!) | * Here is a [http://www.radioreference.com/digital/dig/ICOMSLICER.PDF schematic] (PDF file) for an interface used with [[Trunker]] and a Icom [[IC-R7000]]. For this example, a PRO-43 scanner is used to obtain the data channel. The interface obtains power from the Icom, so there is no issue with weak ports not being able to power the slicer. The IC Chip used is a MAX203 for minimum parts count, but a MAX232 would work just as well. The MAX203 can be obtained from Digi-Key. This interface has also been tested with an Icom R7100. This interface may also work for other radios that use TTL serial levels if another source of 9-12V is available, or 5V if the regulator is left out. (Thanks to Gene!) | ||
+ | * [http://www.swl-remotes.com/pages/13/index.htm IR Remote] | ||
==Supporting Software== | ==Supporting Software== | ||
− | * | + | * Also see the following articles for additional support; |
− | + | ** [[Amateur Radio Transceiver Control]] | |
− | + | ** [[Receiver Software Applications]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | * | ||
− | * [ | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | * | ||
− | * [ | ||
− | |||
− | |||
− | == | + | ==Mailing Lists / forums== |
− | |||
− | |||
− | |||
− | |||
* [http://www.radioreference.com/forums/forumdisplay.php?f=84 Icom Forum at RadioReference] | * [http://www.radioreference.com/forums/forumdisplay.php?f=84 Icom Forum at RadioReference] | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
==eBay Listings== | ==eBay Listings== | ||
Line 112: | Line 78: | ||
[[Category:Desktop Receivers]] | [[Category:Desktop Receivers]] | ||
+ | [[Category:HF Receivers]] | ||
+ | [[Category:Icom Receivers]] | ||
+ | [[Category:Radio Models]] |
Latest revision as of 20:12, 15 November 2020
This page lists links, related pages and software support for the Icom R-7100 receiver. The technical specifications can be viewed here (From the Icom website).
Contents
General Specifications
- 25-2000MHz range
- 900 channels - 9 banks
- 100Hz; 1, 5, 10, 12.5, 20, 25, 100kHz; 1MHz steps
- AM, WAM, WFM, FM, LSB, USB
- Dual scan operation
- Signal meter
- 10 search limits
- Attenuator
- Noise blanker (NB)
- AFC
- Voice squelch control (VSC)
- Autostore (100 channels)
- Clock/timer
- Computer control
- Tape recorder control
- Icom R-7100 Specs
Filters and other Mods
Setting the Output Baud Rate on R7100 Using the Keypad by Greg Knox
1. Turn power OFF
2. While pushing the following keys, turn power ON:
Baud Rate | Keys |
---|---|
9600 | ENT + 5 |
4800 | ENT + 6 |
1200 | ENT + 7 |
300 | ENT + 8 |
Reviews and User Opinions
Related Pages
- Universal Radio R-7100 page
- Javiation R-7100 page
- Donner's Rig Control page
- Radio Database International published a White Paper on this receiver which can be ordered here
- Icom manuals
- R-7100 Service manual (28MB-Pdf)
- R7100 Discriminator Tap Notes
- Here is a schematic (PDF file) for an interface used with Trunker and a Icom IC-R7000. For this example, a PRO-43 scanner is used to obtain the data channel. The interface obtains power from the Icom, so there is no issue with weak ports not being able to power the slicer. The IC Chip used is a MAX203 for minimum parts count, but a MAX232 would work just as well. The MAX203 can be obtained from Digi-Key. This interface has also been tested with an Icom R7100. This interface may also work for other radios that use TTL serial levels if another source of 9-12V is available, or 5V if the regulator is left out. (Thanks to Gene!)
- IR Remote
Supporting Software
- Also see the following articles for additional support;
Mailing Lists / forums
eBay Listings
Back to Icom Radios