Uniden Band Plan Entry
From The RadioReference Wiki
Custom Band Plans for VHF and UHF Voiced - Analog or Digital or Mixed Mode (Analog & Digital) Motorola Type II Trunk Systems require that you enter both a Lower and an Upper Base Frequency value.
Though, APCO P25 Phase I and II systems do not usually require a Band Plan, as it should be carried on the Control Channel, for a slightly distance Site, reliable/initial Reception and Decode may require a "Manual entry" of Custom Band Plan. Here's how to determine these values.
For Site(s) with a single band plan:
- Lower Base Frequency: Base Frequency as provided in the RRDB
- Upper Base Frequency: Lower Freq + (759-Offset) *step
For Sites with multiple Band plans, you need to calculate the upper base frequency for each entry: Upper Basen = Basen + (Offsetn+1 - 1 - :Offsetn)*Stepn
- Where:
- Basen is the lower base frequency for this entry.
- Offsetn+1 is the Offset for the next band plan (for the last table, use 760)
- Offsetn is the offset for this band plan
- Stepn is the step for this band.
For example: Custom Band Plan Frequency Table
Base | Spacing | Offset |
---|---|---|
155.4150 | 15.0 | 380 |
157.2000 | 12.5 | 436 |
157.4700 | 15.0 | 454 |
- Lower Base 1 = 155.4150 MHz
- Upper Base 1 = 155.4150 MHz + (436 - 1 - 380) * 15kHz
- Upper Base 1 = 155.4150 MHz + 55 * 15kHz
- Upper Base 1 = 155.4150 MHz + 0.825 MHz = 156.2400 MHz
- Lower Base 2 = 157.2000 MHz
- Upper Base 2 = 157.2000 MHz + (454 - 1 - 436) * 12.5 kHz
- Upper Base 2 = 157.2000 MHz + 17 * 12.5 kHz = 157.4125 MHz
- Lower Base 3 = 157.4700 MHz
- Upper Base 3 = 157.4700 MHz + (759 - 454) * 15 kHz
- Upper Base 3 = 157.4700 MHz + 305 * 15 kHz = 162.0450 MHz
Typically, Custom Band Plan APCO25 Phase I & Phase 700mhz and/or 800 mhz Band Plans may be needed to be entered as newer, digital trunk systems may have towers point inward; to only cover their jurisdiction, to avoid interference with neighboring jurisdictions. For a proper 'Reception & Decode' may need a Custom Band Plan set - short of moving closer to a single tower. Additionally, adjustment of P25 audio decode level adjustment to Manual mode may be necessary - if you can't reliably receive and decode a System's Site(s). While these shown below don't not include VHF or other UHF ranges, not all Systems will use these below:
Typical Custom Band Plan for a 700mhz Phase I System
Position | Base (Mhz) | Spacing |
---|---|---|
0 | 851.012500 | 12.5 khz |
1 | 762.006250 | 12.5 khz |
Typical Custom Band Plan for a 800mhz Phase I System
Position | Base (Mhz) | Spacing |
---|---|---|
0 | 762.006250 | 12.5 khz |
1 | 851.012500 | 12.5 khz |
Typical Custom Band Plan for a 700mhz Phase II System
Position | Base (Mhz) | Spacing |
---|---|---|
0 | 851.006250 | 6.25 khz |
1 | 762.006250 | 6.25 khz |
2 | 851.012500 | 12.5 khz |
3 | 762.006250 | 12.5 khz |
Typical Custom Band Plan for a 700mhz Phase II System
Position | Base (Mhz) | Spacing |
---|---|---|
0 | 762.006250 | 6.25 khz |
1 | 851.006250 | 6.25 khz |
2 | 762.006250 | 12.5 khz |
3 | 851.012500 | 12.5 khz |
Now, it may seem counter-intuitive that each "Custom Band Plan" not only starts at number 0, and includes a Frequency range that the System's does not use, as well as starting with the "un-needed" frequency range first, the entries must be made to reliably monitor a typical Phase I or II - 700mhz or 800mhz system (or other). Some users, have even noted in the 6th or 7th position a 380 mhz Band Plan or any other unique frequency range appearing in the System's Band Plan Table after decent-to-quality reception (or any position) of a System's Site. These anomalies are not unusual, hence why in many Forums Users ask, "have you tried to drive close to 'tower x' with 'scanner y', While, some do not realize not everyone want's to drive around with a $500 on their passenger seat to, to get the proper "Band Plan" for their "Desktop" scanner. As well its a "User Best Practice", to update their Firmware before any reception or decode issues are posted in the Forums.
For more Info See our Rebanding and Uniden Scanners article and our Software Support for Uniden Rebanding
Return to Wiki page: Programming Your Uniden Scanner
(No matching DB page)