|
|
(11 intermediate revisions by 2 users not shown) |
Line 1: |
Line 1: |
− | These instructions show you how to download and install a completely pre-configured image for the Raspberry Pi2 to function as a broadcast appliance for Broadcastify.com.
| + | #REDIRECT [[Broadcastify Raspberry Pi Image]] |
− | | |
− | This image has only been developed and tested on the Raspberry Pi2 Model B and is not supported on any other model
| |
− | | |
− | This image also has all the precompiled software and configuration files to support the [[Raspberry Pi RTL-SDR Broadcastify]] setup instructions.
| |
− | | |
− | == Purchase Equipment ==
| |
− | | |
− | * Raspberry Pi 2 Model B Project Board - 1GB RAM - 900 MHz Quad-Core CPU - http://amzn.to/1Ku3T9Y
| |
− | * Power Supply for Raspberry Pi - http://amzn.to/1U2r8cD
| |
− | * Memory Card for Raspberry Pi - http://amzn.to/1U2r8JG
| |
− | * Inexpensive USB sound card ($1.70) - http://amzn.to/1hekylB
| |
− | * 1/8 inch audio cable to connect scanner to USB sound card - http://amzn.to/1Kor0NH
| |
− | * Case for Raspberry Pi - http://amzn.to/1JLgNe3
| |
− | | |
− | == Download the Image ==
| |
− | | |
− | * http://s.broadcastify.com/images/bcfy_rpi2_20150821_public.img.gz
| |
− | | |
− | == Install the image ==
| |
− | | |
− | Follow the image installation instructions at the following link on the Raspberry Pi Documentation Page:
| |
− | | |
− | * [https://www.raspberrypi.org/documentation/installation/installing-images/README.md Installing Operating System Images]
| |
− | | |
− | == Initial configuration ==
| |
− | * Boot your Raspberry Pi
| |
− | * Login with username = pi / password = raspberry
| |
− | * Immediately run the raspberry pi system configuration utility
| |
− | pi@bcfypi1 ~ $ sudo raspi-config
| |
− | | |
− | * Choose the second option to change the password for the pi account to your own password
| |
− | * Choose the first option to "Expand Filesystem", then select Finish, and then reboot the device
| |
− | | |
− | == Feed Setup and Configuration ==
| |
− | | |
− | * Plug the USB sound card into the Raspberry Pi
| |
− | * Plug your scanner's headphone jack into the mic jack on the USB sound card dongle
| |
− | * Start alsamixer
| |
− | | |
− | pi@bcfypi1:~# alsamixer
| |
− | | |
− | * press F6, choose the "USB Headphone Set" entry
| |
− | * press your tab key to select the "Capture" device volume control
| |
− | * use your "up arrow" key to adjust the level to it's lowest level possible (6)
| |
− | * press escape to exist alsamixer
| |
− | * run the following command to save the volume settings
| |
− |
| |
− | sudo alsactl store
| |
− | | |
− | * Copy the base darkice.cfg configuration file to darkice1.cfg for the first feed
| |
− | | |
− | sudo cp /etc/darkice.cfg /etc/darkice1.cfg
| |
− | | |
− | * Edit the /etc/darkice.cfg file to match your settings, including the sound card you are using, your feed server, mount, password, and description, then exit and save the file
| |
− | | |
− | sudo nano /etc/darkice1.cfg
| |
− | | |
− | * Enable the feed to start broadcasting at boot
| |
− | | |
− | sudo update-rc.d darkice1 defaults
| |
− | | |
− | * Start your feed
| |
− | | |
− | sudo service darkice1 start
| |
− | | |
− | | |
− | Note: very little volume will be needed from your scanner - adjust the levels as appropriate for a good sounding feed.
| |
− | | |
− | [[Category:Software for Live Audio Broadcasting]]
| |