Difference between revisions of "Uniden Scanner Test Modes for the HP Series scanners"
From The RadioReference Wiki
Line 1: | Line 1: | ||
+ | ==Keypad Options== | ||
+ | |||
{| border="1" cellpadding="1" width="102%" style="vertical-align:top;BORDER-COLLAPSE: collapse | {| border="1" cellpadding="1" width="102%" style="vertical-align:top;BORDER-COLLAPSE: collapse | ||
|'''Test name''' | |'''Test name''' | ||
Line 48: | Line 50: | ||
# MENU --> SETTINGS --> Set Debug Log Mode --> Off | # MENU --> SETTINGS --> Set Debug Log Mode --> Off | ||
# File is in the debug directory on the SD card. | # File is in the debug directory on the SD card. | ||
+ | |||
+ | |||
+ | ==P25 Adjustments using the hidden modes on the SDS100 / 200== | ||
+ | *The P25 filter and P25 mode options is a hidden menu. | ||
+ | *To turn on the hidden menu by going to the Audio Options menu and pressing the blank area in the bottom right corner for 2 seconds or so. | ||
+ | *P25 reception indicator is displayed instead of favorite list name while scan mode. To return to favorite list name turn scanner off then back on | ||
+ | *P25 status : NON/P25/ENC/LNK/DAT Axx or Mxx : A means AUTO. M means Manual. xx is threshold level (8-13). ERR: Error rate. | ||
+ | *Instead of turning the scanner off, leave it in the clock mode and it will retain the manual adjustment setting. | ||
---- | ---- |
Revision as of 09:17, 27 June 2021
Contents
Keypad Options
Test name | Keys | HomePatrol-1 | HomePatrol-2 | BCD436HP | BCD536HP | SDS100 | SDS200 |
Initialize Memory | 1+0+YES+ON | X | X | X | X |
HomePatrol 1/2
- Power off the unit (All Off)
- Pressing the Volume up & Power at the same time until you first see the boot screen quickly release the two and hold the volume down to enter test modes.
- You'll have access to complete Firmware versions as well as many other tools.
- To return to normal scanning power off unit normally and power back on as usual.
Using ProScan with the SDS100
- Select Test and Extras then Protocol Command. In all cases Power Down to exit
- Enter SDR to see the SDR Demo (basically non functional)
- Enter TST,X,UNIDEN_TEST_MODE Caution: This disconnects the serial port
- X equals the following;
- Software Version Display
- Close Call Test
- Unknown
- NWS / SAME test
- Key Touch / Alert LED / Headphone test
- Unknown
- Tone Out Test
Writing a Debug File with the SDS100
- Power up while holding AVOID.(adds Set Debug Log Mode to settings)
- MENU --> SETTINGS --> Set Debug Log Mode --> SD Card File
- Monitor for a bit (a minute or two is plenty).
- MENU --> SETTINGS --> Set Debug Log Mode --> Off
- File is in the debug directory on the SD card.
- The P25 filter and P25 mode options is a hidden menu.
- To turn on the hidden menu by going to the Audio Options menu and pressing the blank area in the bottom right corner for 2 seconds or so.
- P25 reception indicator is displayed instead of favorite list name while scan mode. To return to favorite list name turn scanner off then back on
- P25 status : NON/P25/ENC/LNK/DAT Axx or Mxx : A means AUTO. M means Manual. xx is threshold level (8-13). ERR: Error rate.
- Instead of turning the scanner off, leave it in the clock mode and it will retain the manual adjustment setting.
Categories:
- Uniden Scanners
- Desktop Scanners
- Handheld Scanners
- Mobile Scanners
- Conventional Scanners
- Analog Trunktrackers
- Rebanding Supported Scanners
- Digital Scanners without DMR
- Digital Scanners without MOTOTRBO
- Digital Scanners without NXDN
- Digital Scanners without ProVoice
- Digital Scanners with DMR
- Digital Scanners with MOTOTRBO
- Digital Scanners with NXDN
- Digital Scanners with ProVoice
- Scanner accessories